Rolo01
Thanks, i received your pictures Very interesting: Can you test: grounded A2 pin or not?

bloodworm
Your English I understand, but I can explain my ideas, because I bad know grammar
I try to explain you :
If you know AGP 2.0 and 3.0 specifications, you`ll understand me
VSA, from italian forum, who does overvolt for voodoo5500, says that voodoo5500 gets from AGP slot ONLY VCC3.3V ((pages: 231...233) AB:9,16 and others...) and it`s likely that truth. For test it: I cut off all VDDQ pin`s(about 12 ) and attach to this pin`s external power supply (3.3V) from ATX port. Then i grounded A2 pin *1.5 volt cards tie this signal hard to ground* and turn on the computer. Motherboard get`s 1.5V. My computer not started Then I test when A2 pin not grounded: COMPUTER WORK`S FINE!!!!! when voodoo get`s 3.3V from external power supply...
What do you thinking about it?
PS It`s very hard to do this mod for me: because voodoo russian fan`s not interested in this mod. They fear to kill their voodoo`s
PS2 sorry for my english...

Rolo01
Hi, my e-mail: LLIaJIyH@rambler.ru
Big thanks. I hope you have pictures "fan side" and "back side" with big rezolution

bloodworm
Unfortunately, nowadays voodoo is dead GF2 GTS is more faster and compatible If you think that mod is impossible, you`ll can explain why voodoo5000 and rare voodoo5500 support AGP3.0 ?

Need a pictures VooDoo5 5000\5500 (AGP4X\AGP3.0-support) with a big resolution(mainly AGP port). This pictures maybe helps me to do new mod AGP2.0->AGP3.0 for simple voodoo5 5500 (AGP2.0)
Thanks all!
PS sorry for my english by LLIaJIyH

It`s a very good idea... I`ll try to make that VooDoo5 5500 work`s on an AGP8X board. But I don`t know what pin on AGP get 1,5V\3.3V.

Here`s pictures voodoo 5500.

Fanside:
Image Insert:

103.24 KB

Backside:
Image Insert:

86.21 KB
What Pin I could cut off?
To SuperBox:
Please translate into italian and post it to  http://www.forumzone.it/link.asp?TOPIC_ID=9153 . Maybe trey know what pin get 1.5V\3.3V
Thanks all
PS VooDoo no limits ...

quoting:
7) Back to the voltage modification: to connect the 47k "multi-turns" trimmer we have to remove one resistor, which is located on the upper right corner of the card, near the power connector, where you can clearly see 3 resistors in line. It is the third one if you start counting from the molex; in other words, the latter to the right. You can control its value with your tester (it should be a 17-18k resistor). Well... remove it and solder the 2 wires you are going to connect to the trimmer. Mind to regulate the trimmer in its middle position, before powering up the card.

I mind to the middle position (23,5Kom) and get 3,5V!!! Be carefully!!!  I turn off my computer immediately. Then a mind to ~20 Kom and get  3,25V. My VooDoo work stable at 185Mhz(with this overvolt and original bios 1.18). Before on 185mhz had an artifacts. At 190Mhz has a very-very small artifacts. VSA are cold. Can I get 3.3V ? It`s safely? What maximum voltage are safely (when VAS are cold)?

To Superbox
Translate please into Italian and post it to  http://www.forumzone.it/link.asp?TOPIC_ID=9153 Thanks! And what about RAM overvolt and AGP8X?
Thanks all!
PS sorry for mistakes...

Superbox,Nightbird BIG BIG Thanks
I`ll post my results later...

And small mod voodoo3-2000(up to 170Mhz):


Image Insert:

210.18 KB

Image Insert:

198.48 KB

Image Insert:

138.62 KB

Image Insert:

179.66 KB

Image Insert:

279.97 KB

Image Insert:

203.5 KB

Image Insert:

192.66 KB

Image Insert:

121.1 KB

This is my Mod:

Image Insert:

339.8 KB

Nightbird
Hi, it`a a good idea Thanks...
Here is it: http://www.forumzone.it/link.asp?TOPIC_ID=9153

I`m Russian => bad know english => sorry for mistakes
I made a very cool cooling system on my VooDoo5 5500. Two TT DragonOrb`s 3 . Later i`ll post a picture.
I found reviem about overvolt VooDoo5 5500, but it wrote in italian. I don`t know this language, and web translate into english not helped me  
Where i can read reviem about overvolt VooDoo5 5500 in english ?
Thanks..

sorry for mistakes
I look at the VooDoo5500 AGP Manual and saw description about strange connector   What is "Digital Video Input Connector"? What i can plug to this connector ?

Image Insert:

23.85 KB

ThanK you!!

Sorry for mistakes
I have two VooDoo`s 2 12mb from Diamond. But I haven`t cable for SLI mode. Can I made this cable from Floppy cable? How?
Thank`s