upcoming v5 6000 and stingray 128-3d for sale

Started by Keatah, 07 July 2010, 19:28:51

Previous topic - Next topic

Keatah

Coming soon, for sale

a voodoo 3-3000
2 blackmagic voodoo 2's from stb
an original card from orchid - the first voodoo iteration
3 128-3d voodoo 2 boards with the pro-motion aliance 2d chipset.
a voodoo 5-5500 board
a 2600 voodoo 5-6000 board.
a voodoo volts power unit (if I can find it)
 

Obi-Wan Kenobi

hmm if you claim to have a 3dfx Voodoo5 6000 AGP 128MB rev.A2 2600 + Legacy Voodoo Volts could you post some pictures of it?

If youa re still the owner what country do you come from? So i can add you to my Voodoo5 6000 World owner lists and afterwards edit your name with that of the new owner.

Peace.
Powered By The Force, x-3dfx & The Jedi Academy


Keatah

 

Obi-Wan Kenobi

#4
ahh nice pics, I will some information from you and the card, that are these:

1.) Is it Functional?
2.) Is it Defect?
3.) what Voodoo Volts does it come with:

from left to right:

Large Legacy Voodoo Volts - Small Legacy Voodoo Volts - Late Voodoo Volts


4.) What country are you from, need this to add a flag for your country [8D]

Very interesting to meet another V6K holder, nice E-tag too man, did you work for 3dfx or did you get this card from Clay Woodson< Some history of the card would be interesting as well.

If you like, you can view my lists and my research over here:
http://www.x-3dfx.com/groups/discussion/forum/topic/the-world-voodoo5-5000-6000-lists-info/

3dfxzone.it @ x-3dfx .Yuku are linked from that place as well, if you need to ask anything feel free to do so and I also invite you to x-3dfx.com ;)

Peace man and great to ahve met another unknown Voodoo5 6000 Holder.
Powered By The Force, x-3dfx & The Jedi Academy

Keatah

It *might* have come from clay woodson, that was years ago that I acquired it on a whim. I didn't work for 3dfx. I am just an avid pc hardware buff. I would need to dig thorough emails. I do not know if it working or not. I don't have a motherboard that is compatible with it. In fact, the bx board I have from abit is listed as incompatible!

The voodoo volts, which I have not dug out yet, would be one of the smaller ones. I don't know which one, except it isn't the large one. It is probably the one with the round impression on it. Though that would seem incompatible with the 4-pin connector on the board..??

The two smaller voodoo volts power supplies are, what I hear, pretty much standard units and not specific to 3dfx cards. I *might* have a box of those. I need to go through an extensive locker full of this stuff.
 

Obi-Wan Kenobi

I can help you config a safe 3dfx test setup, my mobo listys shows enough choices for stable runtimes, the EPoX EP-8K3A setries are the best motherboards for all V6K Revisions btw.

All I need to know is what country are you located at, this shows others that read my lists where this card is located ;)
So al I need now is your country [8D]  I think USA but hey I may be mistaken :)
Powered By The Force, x-3dfx & The Jedi Academy

Keatah

yes USA, let me see about getting an epox board then.
 

Obi-Wan Kenobi

QuoteOriginally posted by Keatah

yes USA, let me see about getting an epox board then.

Ahh cools :) the 8K3A+ is the best one, this one has a Code 80 Debug Computer and a raid controller, this is also the most successful motherboard tested with all Voodoo5 6000 revisions.

CPU has to be a 266 or 333 Mhz FSB'ed variant of the AthlonXP my advice is look for an AthlonXP 2600+ and up, the 3200+ FSB 333 is the best CPU for this motherboard, these ryun 2332Mhz default, hereby as being the fastest AthlonXP's around, the 8K3A+ also supports AthlonMP CPU's but no ECC Reg memory as only down side.

As ram goes just use Corsair XMS Platinum or Kingstin Hyper-X PC-3200 this is good ram that also is backwards complaint with PC-2700 aka DDR-333.

Need any help, feel free to ask away [8D]
Powered By The Force, x-3dfx & The Jedi Academy

Obi-Wan Kenobi

#9
QuoteOriginally posted by Keatah

yes USA, let me see about getting an epox board then.

you got an email mate, I found you something ;)
Powered By The Force, x-3dfx & The Jedi Academy

Obi-Wan Kenobi

QuoteOriginally posted by Keatah

yes USA, let me see about getting an epox board then.
Hey Keatah, did you come accross the VoodooVolts yet?
if so Let me know asap.
Powered By The Force, x-3dfx & The Jedi Academy

Keatah

I have not looked through everything yet, I hope to do so soon as I'm looking for a bunch of other stuff too.
 

Obi-Wan Kenobi

#12
ah oke please let me know via email when you have found them :)
Powered By The Force, x-3dfx & The Jedi Academy