Best Mods for V5500 PCI

Started by LW_Hearse, 26 May 2004, 08:59:28

Previous topic - Next topic

LW_Hearse

Hi,

I'm wondering about what people feel are the best mods for a v5500 pci. In terms of bios,cooling,settings and any other factors. As far as cooling size of heatsinks is a factor. I don't want to go too large.

What do you think?

Thanks [?]:D
 

amp_man

What is your RAM vendor and speed? Speed is usually the last digit of the number, somthing like TC6 for 6ns RAM. To convert ns to MHz, divide 1000 by the time in ns, so this is 1000/6ns=166.67MHz. This speed is spec, depending on manufacturer it can go higher. Hyundai can go as high as 200MHz [:p]
When the sun goes down, the music turns up...

Windows XP Pro|Athlon XP 1800+|Voodoo 5 5500 AGP|MSI K7T266-A|768MB DDR 2700 RAM|SonicEdge 5.1 Sound Card

LW_Hearse

Hi,

Good question, Where would I find these numbers? I know the card itself came from Hong Kong.

~Hearse
 

bloodworm

amp-man
the calculation is actually

1/6ns=166.66Mhz
6 nanoseconds is .000000006 seconds (6e-9)
(1/.000000006s=166666666.66Hz) <- notice the Hz and not the MEGAHz...
Bloody Mess

LW_Hearse

Hi again,

The vendor of the chips is Toshiba and there are a string of numbers( can't read em clearly without pulling the card out, disconnecting fans etc etc) followed by T-60

Thanks~Hearse
 

LW_Hearse

Salute! ( that's what us red baron players do)

I was thinking of going with tennmac stealth v3 coolers to replace the stock units. I really don't want to invade on the space of the other slots if possible but am open to suggestions regarding cooling.

Thanks


Image Insert:

28.02 KB
 

amp_man

@bloodworm: It all depends on how much of a smartass you want to act like. Technically, my way works, because I stated that the time was in ns, 1/6 gives you .16667, you need to convert the top or the bottom number. If I had stated 1000/6s, it would be a completely different story. I was simply simplifying a long string of conversions (ns->s, s->Hz, then Hz->MHz) into one equation (ns->MHz)

You have 6ns RAM, which is 166 MHz. This card really isn't worth modding, without some serious attention to RAM cooling, not GPUs.
When the sun goes down, the music turns up...

Windows XP Pro|Athlon XP 1800+|Voodoo 5 5500 AGP|MSI K7T266-A|768MB DDR 2700 RAM|SonicEdge 5.1 Sound Card

LW_Hearse

HI,

serious attention huh? more than just putting heatsinks on em which I would've done?

~Hearse
 

amp_man

QuoteOriginally posted by LW_Hearse

HI,

serious attention huh? more than just putting heatsinks on em which I would've done?

~Hearse

Most likely. Sorry, I was in a bit of a hurry. RAM vendors other than Hyundai don't tend to get much higher than spec speed without artifacts, without complete mods or even ramsinks. Putting new heatsinks on will certainly give you better performance overall, as these cards tend to run hot due to 3dfx's infamous gouping of thermal adhesive, I wish I'd taken pics of mine when I did it. But without a RAM mod, only expect to get around 170~180MHz without artifacts.
When the sun goes down, the music turns up...

Windows XP Pro|Athlon XP 1800+|Voodoo 5 5500 AGP|MSI K7T266-A|768MB DDR 2700 RAM|SonicEdge 5.1 Sound Card

InSomNiaN

LW_Hearse,
The easist way to cool that baby is just to get a couple of cpu fans you are no longer using ( i used my old athlon fans) and attach them to the back of the card. One fan behind each VSA chip.  I was able to go to 190 w/out artifacts with that simple, yet effective mod!! :D
***ASCII stupid question, get a stupid ANSI!***